RB01 Gloss Metallic Fierce Red *SPECIAL OFFER 15% OFF* *DISCONTINUED*

£95.90/span> £112.00
Inc. VAT
Disclaimer
Discontinued products are sold as-is and do not come with any warranty. You agree to our Terms & Conditions when purchasing.

Our Gloss Metallic vinyl wrap has a smooth, high-gloss finish and is crafted from the high-grade polymeric multilayered calendared vinyl film, complete with air release channels. Gloss Metallic wrap is durable and has good conformability; it’s stretchable enough to wrap around every edge and recessed area of your vehicle with ease. Gloss Metallic also uses a safe solvent polyacrylate adhesive, which is easy to install and gentle on car paint.

Specifications

Conformable polymeric material with stable colour pigments. Suitable for full car wrapping (or any other smooth or curved surface).

The thickness of the film: 0.16mm
The thickness of film with release liner: 0.32mm

Type of film: High grade polymeric multilayered calendared vinyl film with air release channels

Colours: Fierce red, Deep blue, Rosaline Pearl, Passionate purple, Passionate purple, Grandeur Plum, Ocean wave, Acid lime, Coral peach, Caribbean blue, Amber brown, Silver chromium, Silver chromium, Dark platinum, Ash Grey, Crystal Silver, Columbia Blue, Sea Turquoise, Cerulean Blue, Ocean Green, Deep Orange, Midnight Purple, Mexican Pink

Width & Length: Standard roll size - 1.52m*18m (59.8"* 708,6", 4.98ft*59ft, 1.66yd* 19,6yd)

Series: 190 series

Adhesive: Solvent polyacrylate

Adhesive performance properties: (1mil adhesive on 1mil material, bonded to stainless steel panel)

180°Peel (PSTC-101), 20 minute bond – 2.2 lb/inch, 24 hour bond – 3.5 lb/inch

Release liner: Kraft white silicone-coated, paper with a double-sided polyethylene coating

Storing period (shelf life): 2 years if stored in +10°C to +20°C, relative humidity 50%, in original package, away from direct sunlight, clean and dry place

Avg. indoor life: 4 years when followed rules of application and usage

Avg. outdoor life: 3 years when followed rules of application and use

Application: from +17°C to +25°C, usage from -55°C to +65°C

Dimensional stability: shrinkage less than 4%

Plastification: between 27%-35%

Breaking Strength: 22.7 N/10mm (Average) Test Method: ASTM D3759/D3759M-057.4 N/10mm (Average)

Light Ageing in UV Exposure: Test Method: ASTM D4329-13 Cycle A & ISO 105-A02:1993/Cor.2:2005,

Test result: 5

Exposure cycle: ASTM D4329-13 cycle A,

Lamp type: UVA-3408h UV at (60±2.5)°C BPT, 0.89 W/ (m2•nm)@340nm, 4h condensation at (50±2.5)°C BPT, Exposure duration: 49h

Recommended application tools: Squeegee, buffer, knife, masking tape, heat gun, magnets, gloves, IRR thermometer, IRR heater

Application method: Standard methods for calendered films. No overstretching. Post heating

Post-heating temperature: 110°C flat surfaces, 130°C curves, and overlaps

Cure time: 24 hours above 10°C

Aftercare: PH neutral, Avoid wax or solvents

Directional: No

Tools: soft squeegees with buffers

Important note: The images, colours, and finishes on screen are approximate. For the real representation of the product always check the colour swatch. Rolls from the same production LOT number should be used for completing a wrap job as a slight batch to batch variation of colour may occur. The film may scratch during the application, or during a day in and out use. The scratching of the film is not covered by the warranty.




Close